In terms of international pricing benchmarks, according to the CP data released by Saudi Aramco, the propane contract price (CP) in March was $895 / ton, up $120 / ton from the previous month, up 15.48% from the previous month and up 43.20% from the same period last year. Butane contract price (CP) in March was 920 US dollars/ton, up 145 US dollars/ton compared with last month, up 18.71% month-on-month, up 54.62% compared with the same period last year; In March, CP in Saudi Arabia rose sharply, giving a strong boost to the international and domestic LPG market. Benchmark LPG prices are higher than a year ago as the economy continues to recover and demand for crude oil continues to repair. According to this trend, the market price of Si3N4 Powder will also be affected to a certain extent.
About Silicon Nitride Si3N4 Powder:
Silicon nitride is a compound of silicon and nitrogen. Si3n4 is the most thermodynamic stable in silicon nitride. It is white, high melting point solid, relative chemical inert, diluted HF and hot H2SO4 attack. It works very hard (8.5 on the MoHS), which has high thermal stability.
Silicon nitride is an inorganic substance, and the chemical formula is Si3N4. It is an important structural ceramic material with high hardness, which has lubricity and wear resistance, an atomic crystal; antioxidation at high temperatures. Moreover, it can resist the impact of the cold and cold, heated into the air to 1000 ° C or more, and the sharp cooling and then heating, and it will not be broken. It is precise because silicon nitride ceramics have such excellent properties, and people often utilize them to make mechanical components such as bearings, air turbine blades, mechanical seals, permanent molds. If silicon nitride ceramics resistant to high temperatures and are not easily transferred, the heat-inspiration surface of the engine member can be improved, not only the quality, but also saves fuel, but also improves thermal efficiency.
Silicon nitride is difficult to produce as a bulk material—it cannot be heated over 1850 °C, which is well below its melting point, due to dissociation to silicon and nitrogen. Therefore, the application of conventional hot press sintering techniques is problematic. Bonding of silicon nitride powders can be achieved at lower temperatures through adding additional materials (sintering aids or "binders") which commonly induce a degree of liquid phase sintering. A cleaner alternative is to use spark plasma sintering where heating is conducted very rapidly (seconds) by passing pulses of electric current through the compacted powder. Dense silicon nitride compacts have been obtained by this technique at temperatures 1500–1700 °C. Feel free to send an inquiry to get the latest price if you would like to buy Silicon Nitride Si3N4 Powder in bulk.
Product Characteristics of Silicon Nitride Si3N4 Powder:
Superior thermal shock resistance
Excellent wear resistance
Good fracture toughness
Mechanical fatigue and creep resistance
Good oxidation resistance
Specification of Silicon Nitride Si3N4 Powder:
Product Name: Silicon Nitride
Particle Size: 0.5um-1um (α phase)
Chemical Composition of Silicon Nitride Si3N4 Powder:
How is Silicon Nitride Si3N4 Powder produced?
The hexagonal β-Si3N4 can directly carry out silicon nitride and nitrogen can be carried out in a 100-1400 ° C.
SiCL4 (L) + 6 NH3 (g) → Si (NH) 2 (S) + 4 NH4Cl (S) under conditions of 0 ° C
3 Si (NH) 2 (S) → Si3N4 (S) + N2 (g) + 3 H2 (g) under the conditions of 1000 ° C
Or use a carbon thermal reduction reaction in a nitrogen atmosphere of 1400-1450 ° C under a nitrogen atmosphere:
3 SiO2 (S) + 6 C (S) + 2 N2 (g) → Si3N4 (S) + 6 CO (g)
However, if the purity of silicon raw materials used will cause silicon nitride produced containing impurity silicate and iron. The silicon nitride synthesized by diamine decomposing is an amorphous shape, and it is necessary to further do an annealing treatment in nitrogen at 1400-1500 ° C to convert it into crystalline powder, and diamine decomposition is only important. Commercially in nitriding method to produce silicon nitride. The carbon-thermal reduction reaction is the simplest way to produce silicon nitride is also the most cost-effective means of manufacturing a silicon powder in industrial.
The electron-level silicon nitride film is made by chemical vapor deposition or plasma enhanced chemical vapor deposition techniques:
3 SiH4 (G) + 4 NH3 (g) → Si3N4 (S) + 12 H2 (g)
3 SiCL4 (G) + 4 NH3 (g) → Si3N4 (S) + 12 HCl (g)
3 SiCL2H2 (G) + 4 NH3 (g) → Si3N4 (S) + 6 HCl (g) + 6 H2 (g)
If you want to deposit silicon nitride on the semiconductor substrate, there are two methods available for use:
The vertical or horizontal tube furnace is performed at a relatively high temperature using low-pressure chemical vapor deposition techniques.
Plasma enhanced chemical vapor deposition techniques are carried out at a relatively low temperature in vacuum conditions.
The cell parameters of silicon nitride are different from single textile silicon. Therefore, depending on the deposition method, the generated silicon nitride film will generate tension or stress. In particular, when using plasma-enhanced chemical vapor deposition techniques, tension can be reduced by adjusting deposition parameters.
The silica was prepared by soluble gel, and then the silicon nanowires were treated with silica gel thereby in which carbon-thermal reduction method and nitride were treated. The special carbon particles in silica gel are produced by glucose at 1200-1350 ° C.
Applications of Silicon Nitride Si3N4 Powder:
Manufacturing structure: such as metallurgy, machinery, aviation, aerospace.
Surface treatment of metals and other materials: such as molds, cutting tools, turbine blades.
Composites: such as metal, ceramic and graphite composite, rubber, plastic
Colorless, transparent self-lubricating wear nanoparticle membrane for mobile phones;
Advanced surface protection such as a car;
Ball valve and part;
Metallurgical, aviation, chemical, energy and machinery industry make parts such as bead/roller bearings, sleeves, valves and other wear;
Making cutting tools, molds, cylindrical wall coating, turbine rotors and blades;
Manufacturing composite materials such as ceramic, graphite, rubber, metal, adhesive, etc.
Nozzle, rocket and missile spray pipe.
Packing & Shipping of Silicon Nitride Si3N4 Powder :
We have many different kinds of packing which depends on the silicon nitride Si3N4 powder quantity.
Silicon nitride Si3N4 powder packing: vacuum packing, 100g, 500g or 1kg/bag, 25kg/barrel, or as your request.
Silicon nitride Si3N4 powder shipping: could be shipped out by sea , by air, by express as soon as possible once payment receipt.
Luoyang Tongrun Nano Technology Co. Ltd. (TRUNNANO) is a trusted global chemical material supplier & manufacturer with over 12-year-experience in providing super high-quality chemicals and Nanomaterials, including boride powder, nitride powder, graphite powder, sulfide powder, 3D printing powder, etc.
If you are looking for high-quality silicon nitride Si3N4 powder, please feel free to contact us and send an inquiry. ([email protected])
Silicon Nitride Properties
|Other Names||silicon (IV) nitride, α-Si3N4, SiN, trisilicon tetranitride, Si3N4 powder|
|Appearance||White to Gray Powder|
|Melting Point||1900 °C|
|Solubility in H2O||Insoluble|
|Electrical Resistivity||11 to 12 10x Ω-m|
|Specific Heat||720 to 800 J/kg-K|
|Poisson's Ratio||0.24 to 0.27|
|Thermal Conductivity||12 to 31 W/m-K|
|Thermal Expansion||2.5 to 3.2 µm/m-K|
|Young's Modulus||140 to 310 GPa|
|Exact Mass||139.943 g/mol|
Silicon Nitride Health & Safety Information
The purchasing pace at the demand end of the international thermal coal market continues to slow down and the international thermal coal price continues to decline. Prices for thermal coal at major international ports continued to fall last week as b…
European Commission President Ursula von der Leyen recently called on India and other countries to support sanctions against Russia over the Ukraine incident. At The Raisina Dialogue forum, von der Leyen said, "We earnestly appeal to all members of t…
To study the problem of collapse mode cracking in the cast-in-place foam concrete wall, using ordinary Portland cement, fly ash, and self-made composite foaming agent as the primary raw materials, the admixtures (there are two kinds of admixtures) we…