Russian President says if the European Union imposes an oil embargo, Europe will buy energy at the most expensive price and economic activity in Europe will weaken. Rosneft needs to change its business model. Russia will help facilitate settlement and access to loans and insurance in its own currency.
According to Reuters, the European Commission will unveil a 210 billion euro plan on how Europe can end its dependence on Russian fossil fuels by 2027 and use its distance from Moscow to accelerate a shift to green energy. According to a draft document seen by Reuters, Brussels will propose a three-pronged plan to wean countries off Russian fuel: switch to importing more non-Russian gas, move more quickly to promote renewable energy, and work harder to conserve energy. The draft measures, which include EU law, non-binding plans, and possible recommendations by national governments, are subject to change before publication.
Austria is not a member of NATO and will not seek membership in the future, the Austrian Foreign Minister said in Brussels recently. He stressed that it was "their choice" for Sweden and Finland to seek NATO membership, while Austria would remain neutral.
The supply and prices of many other TiN powder are expected to continue to be influenced by international situations.
I. Titanium nitride coating (TiN)
TiN coating is a universal PVD coating that improves tool hardness and oxidation temperature. The coating can be used for high-speed steel cutting tools or forming tools to obtain good machining results. TiN coating is pretty economical, it is used to extend the service life of general tools and molds. Its performance is particularly outstanding when it is used to cut copper, low carbon steel, and other soft metals. Coating TiN on the surface of milling cutter can effectively improve the surface hardness of milling cutter, reduce the chemical affinity of milling cutter, prevent adhesion damage in the process of machining, and improve the wear resistance of the milling cutter.
2. Titanium nitrogen carbide coating (TiCN)
The carbon added to the TiCN coating improves tool hardness and surface lubricity, making it an ideal coating for tools. Due to the introduction of carbon element, the surface lubricity of the coating is improved and the friction coefficient is reduced. At the same time, the internal stress of the coating is reduced, which is of great significance to improve the production efficiency and surface quality of the workpiece. TiCN coating has lower friction coefficient and higher hardness than TiN coating. The milling cutter coated with titanium nitride carbide is more suitable for milling stainless steel, titanium alloy, nickel alloy and other hard materials. It has stronger wear resistance and high temperature stability, and can significantly improve the tool life.
3. Titanium aluminum nitride coating (AlTiN)
The alumina layer formed in the AlTiN coating can effectively improve the high temperature machining life of the tool, and the stable oxide layer is formed on the interface between the tool front and chip during cutting, which has good heat insulation performance. AlTiN coatings provide higher surface hardness than TiAlN coatings based on the ratio of aluminum to titanium in the coating, making it a viable alternative coating for high speed machining.
4. Aluminum chromium nitride coating (AlCrN)
AlCrN coating exhibits good red hardness and high temperature stability under high temperature conditions, and has good thermal corrosion performance. When machining low hardness materials or high viscosity materials, the cutting performance is better than AlTiN coated tools. Good adhesion makes it a coating when treating nodules. With this almost invisible coating, milling cutter performance will be greatly improved.
5. CVD diamond coating
Different from single-crystal diamond cutter and PCD composite cutter, CVD diamond coated cutter is a CVD diamond coated cutter which is deposited on the surface of carbide cutter by chemical vapor deposition (CVD) method. In the CVD diamond coating process, the tool surface is pure diamond without any additives, which avoids the application limitations caused by the presence of additive metals in PCD composite films. And the whole deposition process is carried out in atmosphere, there is no special requirement for tool geometry, which can be in any shape of carbide tool surface coating, to meet the needs of complex contour processing.
After experimenting and validation of various cutting tool materials, the service life of CVD diamond coated tools is 8-10 times that of carbide, and its cutting speed is 2-3 times higher than that of cemented carbide cutting tools. It has a good consistency and a low friction factor.
Luoyang Tongrun Nano Technology Co. Ltd. (TRUNNANO) is a trusted global chemical material supplier & manufacturer with over 12-year-experience in providing super high-quality chemicals and nanomaterials including silicon powder, nitride powder, graphite powder, zinc sulfide, calcium nitride, 3D printing powder, etc.
If you are looking for high-quality chemicals, please feel free to contact us and send an inquiry. ([email protected])
Molybdenum disulfide is a solid powder made from natural molybdenum concentrate powder, which is the modern…
Does the high international oil price have an impact on the market of shipment in transit by truck ?…
Does the high international oil price have an impact on the market of poa meaning ?…